<h1>Keyless Entry Remote Programming – 2002 Honda Prelude</h1> <p><font size="3"><b>System Identification:</b> Depending on your vehicle’s configuration, the 2002 Honda Prelude may be equipped with either a Dealer-Installed or Factory-Installed keyless entry system. Follow the correct set of instructions below for your system type. A. Dealer-Installed Keyless Entry System </font></p> <p><font size="3"><b>Important Notes:</b> Entering programming mode will erase all previously stored remotes. Be sure to program all remotes during the same session. Each action must be completed within 5 seconds of the previous one to keep the system in programming mode. </font></p> <p><font size="3"><b>Programming Steps:</b> </font></p> <ul> <li><font size="3">Step 1: Insert the key and turn the ignition to the ON (II) position. </font></li> <li><font size="3">Step 2: Press the LOCK or UNLOCK button on the remote you plan to program. A new, unprogrammed remote may be used. </font></li> <li><font size="3">Step 3: Turn the ignition switch to the OFF (0) position. </font></li> <li><font size="3">Step 4: Repeat steps 1 through 3 two more times using the same remote, for a total of three complete cycles. </font></li> <li><font size="3">Step 5: After the third cycle, turn the ignition to the ON (II) position again. </font></li> <li><font size="3">Step 6: Press the LOCK or UNLOCK button on the same remote. The door locks should cycle, indicating the system is now in programming mode. </font></li> <li><font size="3">Step 7: Program additional remotes by pressing the LOCK or UNLOCK button on each one. The door locks should cycle after each successful remote is added. </font></li> <li><font size="3">Step 8: Turn the ignition to the OFF (0) position to exit programming mode. </font></li> <li><font size="3">Step 9: Test all remotes to ensure they are working correctly. B. Factory-Installed Keyless Entry System</font></li> </ul> <p><font size="3"><b> Important Notes:</b> This system stores up to three remotes in memory. If a fourth remote is added, the oldest one will be erased. Each step must be performed within 4 seconds of the previous. Point the remote at the receiver located near the glove box during programming. </font></p> <p><font size="3"><b>Programming Steps:</b></font></p> <ul> <li><font size="3"> Step 1: Turn the ignition to the ON (II) position. </font></li> <li><font size="3">Step 2: Within 4 seconds, press the LOCK or UNLOCK button on the remote while aiming it at the receiver. </font></li> <li><font size="3">Step 3: Within 4 seconds, turn the ignition to the OFF (0) position. </font></li> <li><font size="3">Step 4: Repeat steps 1 through 3 two more times using the same remote, for a total of three complete cycles. </font></li> <li><font size="3">Step 5: Within 4 seconds, turn the ignition to the ON (II) position again. </font></li> <li><font size="3">Step 6: Within 4 seconds, press the LOCK or UNLOCK button on the same remote. The door locks should cycle to confirm the vehicle is in programming mode. Press the LOCK or UNLOCK button again to finalize that remote.</font></li> <li><font size="3"> Step 7: For each additional remote, press the LOCK or UNLOCK button. The door locks should cycle to confirm each one is successfully programmed. </font></li> <li><font size="3">Step 8: Turn the ignition to the OFF (0) position to complete the process. </font></li> <li><font size="3">Step 9: Test each remote to verify proper functionality.</font></li> </ul>
