2017 Buick Verano

Programming Guide for 2017 Smart Keyless Entry Remote Fob

Important Notice: This vehicle supports key and keyless access systems. If no working key or remote is available, programming procedures may require extended steps or professional assistance. Follow the applicable method below based on your current situation and system type.

Programming a Flip Key – With Two Recognized Keys Available: (For standard key-based ignition systems)

  • Step 1: Sit in the vehicle with all doors closed.
  • Step 2: Insert the first recognized key into the ignition and turn it to the ON/RUN position.
  • Step 3: After a few seconds, turn the key to the OFF position and remove it.
  • Step 4: Within five seconds, insert the second recognized key and turn it to the ON/RUN position.
  • Step 5: After a brief pause, turn the ignition to OFF and remove the second key.
  • Step 6: Insert the new key to be programmed and turn it to the ON/RUN position within five seconds.
  • Step 7: Wait for the security indicator to turn off, signaling successful programming.
  • Step 8: Turn the ignition OFF, remove the key, and test it by starting the vehicle.
  • Step 9: Repeat Steps 2 through 8 for each additional key you wish to program.

Programming a Flip Key – Without Any Recognized Key Available: (Approximately 30-minute procedure – for key-based ignition only)

  • Step 1: Make sure the vehicle is off and all keys you wish to program are available.
  • Step 2: Insert a new key into the ignition and turn it to the ON/RUN position.
  • Step 3: Wait approximately 10 minutes until the security light turns off.
  • Step 4: Turn the ignition to OFF and remove the key.
  • Step 5: Repeat Steps 2 through 4 two more times (three cycles total).
  • Step 6: After the third cycle, turn the ignition to ON/RUN again. The first key will now be programmed.
  • Step 7: To program a second key, turn the ignition OFF, insert the second key, and turn it to ON/RUN.
  • Step 8: Wait a few seconds, then turn the key OFF and remove it.
  • Step 9: Test both keys to ensure they function properly.

Programming a Smart Key – With One Recognized Remote Available: (Keyless access system with push-button start)

  • Step 1: Ensure the vehicle is off. Keep both the recognized and new remotes nearby.
  • Step 2: Remove the emergency key from the new remote.
  • Step 3: Insert the emergency key into the driver’s door lock and turn it to the unlock position five times within ten seconds.
  • Step 4: The instrument panel will display: “Ready for Remote #2, 3, 4 or 5.”
  • Step 5: Remove the cupholder liner from the center console to access the transmitter pocket.
  • Step 6: Place the new remote into the transmitter pocket with the buttons facing up.
  • Step 7: Press the ENGINE START/STOP button. The system will recognize the remote.
  • Step 8: Remove the remote and press the unlock button.
  • Step 9: Repeat Steps 6 through 8 to program additional remotes.
  • Step 10: Once finished, press and hold the ignition button for at least 10 seconds to exit programming mode.
  • Step 11: Test all remotes for lock, unlock, and start functionality.

Programming a Smart Key – Without a Recognized Remote: (Keyless access system – 30-minute procedure)

  • Step 1: Remove the emergency key from the new transmitter.
  • Step 2: Insert the key into the driver’s door lock and turn to the unlock position five times within ten seconds.
  • Step 3: The display will show: “Remote Learn Pending. Please Wait.”
  • Step 4: Wait approximately 10 minutes until the display reads: “Press Engine Start Button to Learn.”
  • Step 5: Press the ENGINE START/STOP button. The system will return to the pending message.
  • Step 6: Repeat Step 5 two more times (three total ignition presses, 10 minutes apart).
  • Step 7: After the third cycle, the display will read: “Ready for Remote #1.”
  • Step 8: Remove the center console cupholder liner to access the transmitter pocket.
  • Step 9: Place the new remote into the pocket with the buttons facing up.
  • Step 10: Press the ENGINE START/STOP button to program the remote.
  • Step 11: The display will prompt to add another transmitter.
  • Step 12: Remove the remote and press the unlock button.
  • Step 13: Repeat Steps 9 through 12 for any additional remotes.
  • Step 14: Press and hold the ignition button for at least 10 seconds to exit programming mode.
  • Step 15: Confirm all remotes are functional.